Difference between revisions of "DRAC Card How To Guide"

From Swivel Knowledgebase
Jump to: navigation, search
 
m (1 revision imported)
 
(No difference)

Latest revision as of 12:52, 11 May 2017



DELL Remote Access Controller How To Guide

Introduction

This outlines the use and configuration of the DELL Remote Access Controller card supplied on the Swivel DELL appliances.


Overview

The DRAC card allows for remote management of the Swivel appliance, and also allows the console to be redirected through a web browser.


Prerequisites

Swivel appliance with DRAC card

Please see the following client-side requirements for each DRAC model respectively:

DRAC 4 - DELL Readme TXT

DRAC 5 - DELL Release Notes PDF

iDRAC 6 - DELL Release Notes PDF

iDRAC 7 - DELL Release Notes PDF


Baseline

DELL PowerEdge R200

DRAC with firmware 1.7


Architecture

Direct connection through cross-over cable or through network hub or switch


DRAC Configuration

Connecting to the DRAC

Direct connection through cross-over cable or through network hub or switch

Configure the client PC with an IP address on the 192.168.0.0 network (excluding 192.168.0.120)

Connect by a web browser to http://192.168.0.120


Login to the DRAC

Login to the DRAC with the following:

Username: root

Password: calvin


DRAC login.JPG


Configure the DRAC Network Interface

From the DRAC menu select Configuration, and then Network. Change the Network settings to the desired values.


DRAC Network Configuration.JPG


Changing Network values will result in loss of connectivity through the old IP address.


DRAC Network configuration changes.JPG


Console redirect through the DRAC Network Interface

The DRAC can redirect from the console of the appliance to a web browser session. Select Console then Console Redirect.


DRAC Console redirect.JPG


This will open up a Security Warning box asking to run the application, select Run.


DRAC Console redirect Signature Error.JPG


A window will open allowing access to the console.


DRAC Console.JPG


Console configuration of the DRAC Interface

Connect to the PINsafe server through the management console connecting a monitor to the VGA port of the DRAC card. Wait for the DRAC configuration option, and press CTRL-D to enter the options menu.


IP address of the DRAC from the Command Line

Login to the CMI and select the Advanced options to get command line access then run the command racadm getniccfg

Example:

  racadm getniccfg
  NIC Enabled = 1
  DHCP Enabled = 0
  IP Address = 192.168.0.120
  Subnet Mask = 255.255.255.0
  Gateway = 192.168.0.1


DRAC reset account password

How to reset config if you cannot remember the password.

You can only do this from the O/S

tool required: racadm

  1. This will reset the first account to the default password: calvin
  1. to find out the user name of the first account (1) use the following command

/opt/dell/srvadmin/sbin/racadm getconfig -g cfgUserAdmin -i 1

  1. now to reset that password use the following command

command line: /opt/dell/srvadmin/sbin/racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 "calvin"


If you are unable to access via O/S you will need to boot with System Rescue CD

press F11

Then select SATA CD-ROM device

When prompted press Enter (too select the default boot option)

select 40 for keyboard type (UK)

Once you are at command prompt issue the following commands.

ifconfig eth0 192.168.0.99 netmask 255.255.255.0

route add -net 0.0.0.0 netmask 255.255.255.0 gw 192.168.0.254

passwd

You will now be prompted for passwd please enter lockbox

Find out user name: racadm getconfig -g cfgUserAdmin -i 1

Now issue the command: racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 "calvin"