Webmin How To Guide
Contents
Overview
Webmin is a third party package present on Version 2 and Version 3 Swivel Appliances. It has many administrative uses which are of particular use during a support incident, rather than day-to-day administration:
- Retrieving files from the Swivel appliance;
- Inspecting the MySQL Swivel database;
- Stopping or Starting services.
Webmin is often useful when it is not possible to get a connection using PuTTY or WinSCP over SSH, such as when access is restricted. For more information on using PuTTY and WinSCP, see the PuTTY How To Guide and WinSCP How To Guide.
This article describes how to login to Webmin on an appliance. To discover more about how Webmin can be used to support Swivel, see the Common Uses for Webmin section below.
Prerequisites
- Swivel version 2 appliance (hardware or virtual machine) with Webmin installed;
- Web browser to connect to the Swivel server: Note that Internet Explorer is not suitable for use with Webmin, for technical reasons;
- Webmin login credentials.
Accessing Webmin
The default credentials are:
Username: admin Password: lockbox
The default URL for Webmin is:
https://192.168.0.35:10000/
(where 192.168.0.35 is replaced by your Swivel appliance IP. By default a single appliance is 192.168.0.35 and primary and secondary appliances are by default 192.168.0.36 and 192.168.0.37 respectively).
Logging in
Using a Web browser, visit the URL given above (https://192.168.0.35:10000/) using the IP address or hostname you have assigned to your Swivel appliance.
You should reach the following page, where you can enter the default credentials given above, to login:
Once logged in, you should see the following screen:
If for some reason you cannot establish a connection to the web page, then consult the Troubleshooting section below.
Webmin guides
128-bit encryption enforcement How to Guide
Troubleshooting
Changing the Web Certificate
The instructions below describe how to install a 2048-bit certificate for Webmin (original source: http://blog.rimuhosting.com/2014/11/18/webmin-sec-err-invalid-key/).
* Log into the appliance console. * Go to Advanced Menu, Command Line. If you do not know the command line password, please contact support@swivelsecure.com * Enter the following commands:
file=/etc/webmin/miniserv.pem openssl req -x509 -newkey rsa:2048 -keyout $file -out $file -days 3650 -nodes -subj \ "/C=GB/ST=West Yorkshire/L=Wetherby/O=Swivel Secure/CN=pinsafe.swivelsecure.com" openssl x509 -x509toreq -in $file -signkey $file >> $file service webmin restart
In the above commands, replace the subject with values appropriate to your own country, state, city, company and server name.
Cannot Access Webmin
Is port 10000 being specified?
Is network access to the appliance available, can you ping the appliance?
Is port 10000 blocked by a firewall? Can you telnet to port 10000
Is SSL specified in the request using https?
IE / Firefox will not login to Webmin
This affects appliance versions up to 2.0.14 and is due to Internet Explorer preventing login to websites with key lengths of less than 1024 bits. Recent versions of Firefox also exhibit the same behaviour. Use another web browser to access the appliance or upgrade to a more recent version of appliance.
If you do not wish to use an alternative browser, then you can enable the "Continue to this website" button in IE, by running the following command on the Windows Command Line:
certutil -setreg chain\minRSAPubKeyBitLength 512
This is mentioned in the article:
http://support.microsoft.com/kb/2661254
If you want to revert this change, run:
certutil -delreg chain\MinRsaPubKeyBitLength
If you prefer to update your certificate to 2048 bits, use the routine detailed above to change the certificate.
Webmin not running?
If you find that you cannot obtain Webmin access, check to see that Webmin is listening for connections. Login to the appliance via SSH using PuTTY (see the PuTTY How To Guide) and get to the command line:
Enter the following netstat command. If you return a result similar to this then you know that Webmin is installed and running.
[admin@appliance ~]# netstat -anp | grep 10000 tcp 0 0 0.0.0.0:10000 0.0.0.0:* LISTEN 3594/perl udp 0 0 0.0.0.0:10000 0.0.0.0:* 3594/perl [admin@appliance ~]#
If this returns nothing then it could indicate that Webmin is not installed. If this is the case try running the following commands to see if the package exists on the appliance:
[admin@appliance ~]# find /etc/ -iname webmin /etc/sysconfig/daemons/webmin /etc/pam.d/webmin /etc/webmin /etc/webmin/webmin /etc/rc.d/init.d/webmin [admin@appliance ~]#
Also:
[admin@appliance ~]# whereis webmin webmin: /etc/webmin /usr/libexec/webmin [admin@appliance ~]#
If you don't return a result, then it's likely that your appliance is too old to have Webmin installed. If you do return a result then you can use the following stop and start commands to get Webmin stopped and started:
[admin@appliance ~]# service webmin stop Stopping Webmin server in /usr/libexec/webmin [admin@appliance ~]# service webmin start
A further check of the listener will confirm if Webmin is now started:
[admin@appliance ~]# netstat -anp | grep 10000 tcp 0 0 0.0.0.0:10000 0.0.0.0:* LISTEN 3185/perl udp 0 0 0.0.0.0:10000 0.0.0.0:* 3185/perl [admin@appliance ~]#
If you're not bringing up anything via a Web Browser check that there are no firewalls between you and the Swivel appliance which could be obstructing access. Try the following command to reveal the Swivel firewall entries, to ensure that the Swivel appliance is allowing access to the Webmin listener:
[admin@appliance ~]# cat /etc/sysconfig/iptables
This will produce the following output.
Ensure that the following ACCEPT line (highlighted in the output above) exists, to be sure that Swivel is allowing access to the Webmin listener:
-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 10000 -j ACCEPT
Webmin inaccessible after patch upgrade
Edit the file /etc/webmin/miniserv.conf locate the line ssl_version=10 line and remove it. Restart webim with;
service webmin restart
Locked out of Webmin?
Using the PuTTY How To Guide SSH to the appliance, goto the Command Line and enter the following command:
/usr/libexec/webmin/changepass.pl /etc/webmin/ admin lockbox
This will reset the password for the admin user to lockbox.
Common Uses for Webmin
Below are articles which describe common use cases for Webmin:
